READ THIS FIRST:
Check the pack and make sure you have all of the parts
listed on the front of this booklet. If not, contact the
supplier where you bought this product.
IMPORTANT SAFEGUARDS:
When using an electrical appliance, basic safety
precautions should always be observed, including the
following:
Ensure the feet are correctly attached before use.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Extreme caution is necessary where children or persons
with reduced physical, sensory or mental capabilities may
come into contact with the heater when in use.
The product is for household/office use only.
WARNING
- In order to avoid
overheating do not cover or
obstruct grilles or air intake
openings when in use.
Do not place the heater on carpets with a very deep
pile.
Always ensure that the heater is placed on a firm level
surface and ensure that the heater is not positioned close
to flammable materials, such as curtains, drapes etc as this
could create a fire hazard.
The heater must not be located adjacent to or against
an electrical socket.
Do not run the cord under carpets/rugs.
Arrange the cord away from high traffic areas and
where it will not become a trip hazard.
Keep the mains lead away from the heater when in use.
Do not operate the heater with a damaged cord/plug
or if the heater malfunctions.
If the supply cord is damaged, it must be replaced by a
qualified engineer.
Avoid the use of an extension cord as this may overheat
and cause a risk of fire.
Do not use the heater in any areas where petrol, paint
or other flammable liquids or flammable fumes may be
present e.g. garages or workshops.
Do not use this heater in the immediate surroundings
of a bath, shower, swimming pool or where water is
present.
This heater is hot when in use. To avoid burns and
personal injury, do not let bare skin touch hot surfaces.
Never leave the heater unattended whilst it is in use.
SPECIFICATION:
VOLTAGE: 220-240V~50-60Hz
POWER MAX: 2kW
WARNING:
The heater should never be used without the feet
securely fitted.
This product must only be operated in an upright
position.
Do not try to repair the heater yourself, always
consult a suitably qualified engineer.
Do not use the heater in small rooms when they are
occupied by persons who are not capable of leaving
the room on their own, unless constant supervision is
provided.
OPERATION OF THE HEATER:
NOTE:
It is normal for the heater to smell slightly for a
short while when turned on for the first time or after a
period of not being used.
ATTACHING THE FEET:
1. Tip heater upside down.
2. Attach feet to each end of the heater using the
screws provided. Affix the feet using 2 screws
diagonally to correspond with the pre cut holes.
Fasten securely.
3. Turn heater correct way up.
INSTRUCTIONS FOR USE
/ FAN OPERATION:
This heater also incorporates an internal fan, which
can be switched on independently of the heating
elements.
This is operated by turning the switch on to the “fan”
symbol (opposite).
The fan will only operate with the thermostat in the
“on” position and can be used when the heating
elements are “on” to blow warm air into the room.
In warm conditions the fan can be used with the
heating elements “off” to blow cool air into the room.
Choose a suitable location for the heater, taking into
account the safety instructions above.
Insert the plug of the heater into a suitable socket.
Turn the thermostat knob fully in a clockwise direction
to the maximum setting.
Turn on the heating elements by means of the
rocker switches on the side panel. When the heating
elements are on the switches will illuminate. For
maximum heat output both switches should be on.
Example:
Switch 1 = 750W | Switch 2 = 1.25kW | Combined = 2kW
When the desired room temperature has been
reached, the thermostat knob should be turned slowly
anti-clockwise until the thermostat click is heard and
the lights on the element switches are seen to go out.
After this the heater will keep the air temperature in
the room at the set temperature by switching on and
off automatically.
Model Identifier(s):
CONVHTSTD
CONVHTFAN
CONVHTTIM
Heat output
Nominal heat output
Pnom
2.0
2.0
2.0
kW
Minimum heat output
(indicative)
Pmin
0.75
0.75
0.75
kW
Maximum continuous
heat output
Pmax,c
2.0
2.0
2.0
kW
Auxiliary electricity consumption
At nominal heat output
elmax
N/A
N/A
N/A
kW
At minimum heat output
elmin
N/A
N/A
N/A
kW
In standby mode
elSB
N/A
N/A
0.00091
kW
Type of heat output/room temperature control
With mechanic thermostat room temperature control
Yes
Contact details: Eterna Lighting Ltd, Huxley Close, Wellingborough, Northamptonshire NN8 6AB
