ETC ColorSource Spot jr Installation Manual Download

Page: 11 / 12

ETC Installation Guide

ColorSource Spot jr

Press the Mode button to start the update process.

•

The display will alternate between

Udt

and the percentage

complete while updating.

•

The fixture will reboot once the update is complete.

Reconnect DMX In on the fixture.

Restore Factory Defaults

Press and hold the Mode button, Up button, and Down button
simultaneously for 5 seconds. The DMX start address will blink once to
confirm that defaults have been restored.

Error Codes

There are three error codes that may be shown on the user interface.

•

CAL

: Screen toggles between

CAL

and

ERR

to indicate a problem with

the color calibration. The fixture will need to be returned to the ETC
factory; contact your local dealer to set up a repair.

•

OtP

: Screen toggles between

OtP

and

ERR

to indicate that the fixture

has gone into over-temperature protection mode to avoid damaging
the fixture. Once the fixture has self-cooled, the error will automatically
clear.

•

No App

: Screen toggles between

and

APP

to indicate that the

upgraded fixtures have a software issue. Reload software to clear the
error. If the error persists, contact ETC.

RDM Values

Parameter

Fixture

Value

Description

Manufacturer ID

All

0x6574

Electronic Theatre

Controls

Model ID

ColorSource Spot jr

0x0219

ColorSource Spot jr

Deep Blue

0x021A

DMX Start

Address

All

0x00F0

Range = 1–512

DMX Personality

All

0x00E0

1 = 5 Channel

2 = Direct

3 = 1 Channel

4 = RGB

Output Frequency All

0x8123

0 = Standard (1.2 kHz)

1 = High (25 kHz)

ColorSource Spot jr

Page 11 of 12

ETC

Summary of Contents for ColorSource Spot jr













Search results

Summary of Contents for ColorSource Spot jr

Reviews:

Related manuals for ColorSource Spot jr

Brands by name

Popular brands

ETC ColorSource Spot jr, Installation Manual

Search results

Summary of Contents for ColorSource Spot jr

Reviews:

Related manuals for ColorSource Spot jr

Brands by name

Popular brands