background image

ETC Installation Guide

ColorSource Fresnel V v1.1

FCC Compliance

ColorSource Fresnel V

(For any FCC matters):

Electronic Theatre Controls, Inc.
3031 Pleasant View Road
Middleton, WI 53562
+1 (608) 831-4116

etcconnect.com

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation. Visit

etcconnect.com/products

for current and complete compliance

information including FCC compliance.

Note:

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. Any modifications or
changes to this product not expressly approved by Electronic
Theatre Controls, Inc. could void the user’s authority to operate
the product. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be
required to correct the interference at their own expense.

This device contains a wireless module with the following identification
numbers:

FCC ID: VU65995

ISED Compliance

This device contains a license-exempt transmitter/receiver that complies
with Innovation, Science, and Economic Development Canada’s license-
exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Contains IC ID: 7480A-5995

CAN ICES-005 (A)

ColorSource Fresnel V

Page 15 of 16

ETC

Summary of Contents for ColorSource Fresnel V

















Reviews: