background image

www.etsolar.hk 

- 9 - 

 

 

Do not disconnect under load'

 

Operation and Maintenance 

 

It  is  required  to  perform  regular  inspection  and  maintenance  of  the  modules, 
especially during the period of warranty. inform the supplier within 2 weeks when 
modules are found to be defective. 
ET  Solar  recommends  the  following  maintenance  items  to  ensure  optimal 
performance of the module. 

 

6.1 Cleaning 

 

This manual covers the requirements for the cleaning procedures of ET Solar PV 
modules.  Professional  installers  should  read  these  guidelines  carefully  and 
strictly follow these instructions. Failure to follow these instructions may result in 
death,  injury,  or  property  damage.  Damages  induced  by  inappropriate 
cleaning procedures will void ET Solar warranty.   

 

The amount of electricity generated by a solar module is proportional to the 
amount of light captured. A module with shaded cells generate less energy, 
and therefore, it is essential to keep PV modules clean. The dirt such as bird 
droppings, leaves, dust is usually need to be cleaned.   

 

When  cleaning  the  modules,  make  sure  that  the  temperature  difference 
between the water and the module is in the range of -5

-10

.   

 

Use a dry or wet, soft and clean cloth, sponge, or soft bristled brush to wipe the 
photovoltaic module. Please make sure that the cleaning tools do not wear 
out glass, EPDM, silicon, aluminum alloys or steel.   

 

If  there  is  greasy  dirt  or  other  substances  which  are  difficult  to  clean, 
conventional household glass cleaning agents can be used. Pay attention not 
to use alkaline and strong acidic solvents, including hydrofluoric acid, alkali, 
acetone.   

 

For modules that are installed horizontally (0° tilt angle),   
they should be cleaned more frequently, as they do   
not have"self-cleaning" function as those installed at   
10° or larger tilt angles.   

 

The back surface of the monofacial module usually 
does not need to be cleaned. When cleaning the back   
of the bifacial module, avoid any sharp objects that   
may cause damage or penetrate the base material. 
The other cleaning requirements are the same as the front-side. 

 

 

 
 

Summary of Contents for ET-M660BH GL Series




















Reviews: