ESTeem 195Ep Quick Start Manual Download Page 5

APPENDIX G

QUICK START GUIDE

 

 

Revised: 14 Jun 06 

APX G-5 

EST P/N AA107G 

Note: This program is saved in a compressed file format.  
Microsoft Windows XP® will open the file directly, but other 
operating systems will require a common compression program 
such as WinZip available for download at 

http://www.winzip.com

 

 
Double click on the 195EdiscoverySetup.exe file listed in the 
window to install the program. 
 
5.

 

Set IP Address on the 195Ep

.  Connect the Model 195Ep to 

your computer either direct to the Ethernet card or through a 
HUB/Switch using a CAT-5e Ethernet cable.  The Ethernet 
port on the 195Ep supports Auto-Negotiation so either a 
patch cable or crossover cable will work.  Open the ESTeem 
Discovery Program and press the Discover Modems button.  
The Model 195Ep will be displayed in the program by the 
Ethernet MAC address and Current IP Address (Figure 3).   

Note:  The SSID and Mode of Operation will be adjusted 
later in the configuration.    

 
Double-click on the 195Ep you wish to program and the 

Configure IP Address

 window will be displayed (Figure 4).  Enter an 

IP address and Subnet Mask for the 195Ep that matches your network subnet and press the OK button to save this to the 
ESTeem.  You will receive notification that the Configuration was Successful and the 195Ep will reboot.  Proceed to ESTeem 
Setup to continue configuration.  

 

Setup Programming 

 
You should now be ready to configure the Model 195Ep through your web browser.  Open the web browser program and enter the 
IP address of the ESTeem in the address line and press enter.  
 

 

Figure 2- ESTeem Utility Download 

 

Figure 3 – Discovery Program Main Page 

 

Figure 4 – Change IP Address Window 

Summary of Contents for 195Ep













Reviews: