EST APC-TF Series User Manual Download Page 21 | Manualshive

Page: 21 / 24

background image

Copyright 2003-2013 CSM CO.,LTD

- 21 -

APC-TF Series MAINTENANCE - Fuses

DANGER!

The controller must be maintained by personnel qualified and trained to work
with low voltage electrical equipment in an industrial environment.

The user’s installation must be protected upstream (non high-speed fuses,
thermal or electromagnetic circuit breaker, suitable fuse-isolator) and must
comply with current standards.

FUSES

Protection of auxiliary voltage connection

Protection fuses for both the fan connection (90A nominal current unit) and separate electronics
supply must be installed in each conductor connected to a supply phase.

Auxiliary
voltage (max.)

1A T-TYPE fuse
5.0 x 20 mm

Remarks

250V

fuse

PCB_type

* Recommended fuse for auxiliary voltage connection

«
...
19
20
21
22
23
...
»

Summary of Contents for APC-TF Series

























Reviews:

No comments

Related manuals for APC-TF Series

Brand: Eaton Pages: 12

Brand: jbc Pages: 44

Brand: jbc Pages: 8

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 11

Brand: Nauticam Pages: 2

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 20

GEMINI C Series

Brand: NAPCO Pages: 24

Brand: U-Prox Pages: 3

Brand: Xilinx Pages: 52

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands