background image

 

15 

Note: 

If you trip a beaker or blow fuse, turn off the equipment off, then reset the breaker or 

replace the fuse. 

 
Note:

 Remove all sawdust from the house as you empty the dust bags.  Empty your sander bags 

when they are ½ full, this will help with the dust pick up.  Sawdust can be flammable and you do not 
want it in your house.   
 

Note:  

When using the SL -7 edger, sand from right to left and let the edger do the work.  A 

properly aligned edger, with a disc pad in good condition will function well without the user exerting 

additional pressure.  Let the edger do the work; don’t put extra pressure on the machine.  Work at 

a pace you are comfortable with, and take frequent rests.    
 

 If the cutting action of you sander seems to slow or diminish, it is probably time to change the sandpaper.  In an effort to 

save money, don’t try to extend the life of the paper, replace it as needed.  If you skimp on the amount of paper you use on 
this project it will affect the end result.  Don’t look at the co

st at the time of sanding, but rather over the life of the floor.  

Replace abrasives to get the same type of cut across the floor.  

 
After you sand the floor with the SL-8 & SL-7 it is time to scrape corners, door jambs, etc.  Use our 12 wood handle scraper 
with a 1” Red Devil blade, available from the rental store, to accomplish this task.  Hand sand the areas you scraped. 
 
If you have areas such as baseboard heat, radiators or toekicks that could not be reached by the SL-7, use the Silver-Line 
U2 underradiator sander to clean up these areas.  It uses 5” PSA discs and is also available at the rental store.   
 

When your done sanding your floor return your sanders to the rental store.  Remember to return the cords, wrenches, bags 
and unused supplies.   
 

Note: 

After sanding you should screen the floor before you apply any finish or stain to achieve the 

best possible finish.  A professional floor sander will screen his work; spend the time and money to 
screen your floor.   
 

Essex Silver-Line Corporation 

PO Box 40 

1118 Lakeview Ave. 

Dracut, MA  01826 

(978) 957-2116, Fax (9780 957-6989 

Toll Free 800 451-5560 

 

www.essex-silver-line.com 

 
 
 

Summary of Contents for Silver-Line SL-8


















Reviews: