Esse Ironheart EW North American Instructions Download Page 32 | Manualshive

Page: 32 / 44

background image

Page 32

IH (NA) R4 201102

Figure 15 50mm (2") Clearance to Combustible Wall Member

Method D

Start with a Solid-Pak listed factory built chimney section at least 305mm (12”)
long, with insulation of 25mm (1”) or more, and an inside diameter of 203mm
(8”) (50mm (2”) larger than the 152mm (6”) chimney connector). Use this as a
pass-through for a minimum 24 gauge single wall steel chimney connector. Keep
the  Solid-Pak  section  concentric  with  and  spaced  25mm  (1”)  off  the  chimney
connector by way of sheet metal support plates at both ends of the chimney
section.  Cover  openings  with  and  support  the  chimney  section  on  both  sides
with  24  gauge  minimum  sheet  metal  supports.  Ensure  that  the  supports  are
fastened securely to wall surfaces on all sides.

Notes:

o

Connectors to a masonry chimney, excepting method B, shall extend in
one continuous section through the wall pass-through system and the
chimney wall, up to but not past the inner flue liner face.

o

A chimney connector shall not pass through an attic or roof space, closet
or similar concealed space, floor, or ceiling.

Chimney Height

A masonry chimney or a listed factory-built chimney must be the required height
above the roof and any other nearby obstructions. The chimney must be at least
90cm (3’) higher than the highest point where it passes through the roof and at
least 60cm (2’) higher than the highest part of the roof or structure that is within
3m (10’) of the chimney measured horizontally.

«
...
30
31
32
33
34
...
»

Summary of Contents for Ironheart EW













































Reviews:

No comments

Related manuals for Ironheart EW

Brand: Teba Pages: 14

Brand: Kalor Pages: 142

Brand: Quadra-Fire Pages: 16

Brand: Pacific energy Pages: 32

Brand: Yakar Pages: 14

Brand: Astra Pages: 28

Brand: Seaward Pages: 8

Brand: Sears Pages: 4

Brand: Nibe Pages: 40

American Harvest 6037

Brand: USSC Pages: 24

Brand: GARDECO Pages: 12

Brand: Coleman Pages: 2

Brand: Coleman Pages: 2

Brand: Coleman Pages: 16

Brand: Palazzetti Pages: 104

Brand: Oak Stoves Pages: 24

Brand: Gasmate Pages: 2

Brand: Bosca Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands