6
Operator's Manual
Propane Powered Ice Auger
Check for parts online at
www.GetEskimo.com
or
call
800-345-6007
M-F 8-5 CDT
WARNING
•
NEVER RUN ENGINE INDOORS. EXHAUST
FUMES ARE DEADLY.
•
DO NOT USE AN ICE AUGER FOR ANYTHING
OTHER THAN ICE.
•
THE ICE AUGER BLADE PROTECTOR SHOULD BE
ATTACHED TO THE AUGER BLADE WHEN NOT IN
USE. THIS WILL PROTECT THE CUTTING EDGE OF
THE ICE AUGER BLADES. AVOID INJURY! MAKE
SURE THE UNIT IS IN A STABLE POSITION BEFORE
PULLING THE STARTER HANDLE.
CAUTION
•
AVOID INJURY! IF AUGER IS MOUNTED TO
ENGINE, ALL SAFETY GUARDS MUST BE SECURELY
FASTENED TO AVOID SERIOUS INJURY.
•
AVOID INJURY! IF ENGINE FAILS TO START AFTER
TRYING STARTING PROCEDURES, PLEASE CONTACT
OUR CUSTOMER SERVICE DEPARTMENT AT
800-345-6007 OR VISIT WWW.GETESKIMO.COM.
•
AVOID INJURY! NEVER LEAVE ENGINE RUNNING
WHILE UNATTENDED. TURN OFF AFTER EVERY USE.
•
AVOID INJURY! NEVER CARRY POWERHEAD
AND AUGER BETWEEN HOLES WHILE ENGINE IS
RUNNING.
PRE-OPERATION
Preparing Engine For Starting
1. Check engine oil level (see Check Oil Level in Service,
Troubleshooting, and Repair section).
2. Thread a 16.4 oz disposable propane fuel cylinder into
the regulator. Ensure the cylinder is fully sealed.
NOTE: The correct size disposable propane fuel cylinder
is approximately 3.875 inches (9.5 cm) in
diameter. Always use the correct size and type
specified. Use of the wrong propane cylinder
can cause damage to engine. It is recommended
that you have at least one additional disposable
propane cylinder available to use as a back up.
3. Install the cylinder into the holder and secure it down.
STARTING
1. Turn on/off valve to “ON” until it positively engages into
the on position. Always check for leaks before using.
2. While holding onto the handle bar with your right hand
(unit in the vertical position), grasp the starting handle
and pull slowly until you feel the recoil engage the recoil
clutch, then swiftly pull using full arm strokes until the
engine starts. Do not hold the throttle to start.
IMPORTANT NOTE:
When first using a newly purchased unit, or after long
storage, it may require 6-10 pulls initially to prime the
system. After first use, each subsequent start should only
require 1 to 2 pulls to start.
IMPORTANT NOTE:
When using unit in extreme cold conditions, if unit does
not fire initially without touching the throttle, hold throttle
at fully open and repeat the starting procedure. After the
engine fires, release the throttle for safety.
IMPORTANT NOTE:
If the engine does not start in excessive cold conditions,
replace the propane cylinder with a new cylinder that has
been stored in a warm place. Alternatively, you can move
the auger to a warm place to allow the auger to warm up
sufficiently to start.
IMPORTANT NOTE:
The clutch will transfer maximum power after about two
hours of normal operation. During this break-in period
clutch slippage may occur. The clutch should be kept free
of oil or other moisture for efficient operation.
IMPORTANT NOTE:
Drill holes without placing body weight on the unit.
The auger operates most efficiently with a shaving
action caused by the weight of the unit itself.
IMPORTANT NOTE:
DO NOT allow the recoil to snap back quickly, guide the
handle slowly back to the rest position.
OPERATION
1. After starting the engine, allow the engine to idle for at
least 30 seconds in preparation for usage.
2. Place auger in position for hole to be drilled, hold unit at
full throttle, avoid putting down force on the unit, and
allow the weight of the unit to do the work for you.
3. When finished drilling the hole, turn the on/off valve to
the “OFF” position.
MAINTENANCE AND STORAGE
Auger Maintenance
1. The gear case has 4 oz. of lithium grease installed at the
factory. It is recommended that once a year the gear case
be split and the grease level checked. Add grease only if
level of grease is below top of the gears. DO NOT OVERFILL.
2. Keep all screws, nuts, and bolts tight.
3. Always replace blade protector when power auger is not
in use.
4. If blade performance decreases, turn unit off and disconnect
spark plug wire. Carefully inspect cutting edge of blades for
any nicks or shiny areas. If blades show any of these signs,
they need to be resharpened or replaced.