Details of EZ-Programming
Display Contrast
Contr 1- 5
(Contrast adjustment)
In this setting, Solo S2 allows you to scroll though 5
levels of contrast adjustment for optimum viewing.
Pilot Light (12-volt power only)
PilotHWY
(Full description)
In this setting, Solo S2 will display “Highway,” “City,”
or “Auto” as its power-on indication. (factory default)
Pilot H
(Letter)
In this setting, Solo S2 will display “H” for Highway,
“C” for City, and “A” for Auto.
Pilot H.>
(Letter with scanning dot)
In this setting, Solo S2 will display “H” for Highway,
“C” for City, and “A” for Auto. Also, a single dot will
continuously scroll across the display.
Pilot+
(Symbol)
In this setting, Solo S2 will display “+” for Highway,
“.” for Auto, and “–” for City.
17
16
Pilot+.>
(Symbol with scanning dot)
In this setting, Solo S2 will display “+” for Highway,
“.” for Auto, and “–” for City. Also, a single dot will
continuously scroll across the display.
Pilot+>
(Scanning symbol)
In this setting, Solo S2 will display “+” for Highway,
“.” for Auto, and “-” for City. Each will continuously
scroll across the display.
Auto Power
aPwr On
(Standard)
In this setting, Solo S2 maximizes battery life by
intelligently shutting down once your vehicle has
become motionless. Approximately 15 minutes after
the vehicle has stopped moving, the Solo S2 will go
into a “sleep” mode. It will “sleep” for approximately
30 minutes. However, if the Solo S2 senses movement
within this “sleep” time, the Solo S2 will prompt you
(both audibly and visually) to see if you would like to
return to an active mode. If yes, simply press any
button.
If not, the Solo S2 will shut off completely,
maximizing battery life.
aPwr OFF
In this setting, Solo S2 requires that you turn it on and
off manually using the PWR button.
Power-on Sequence
PwrOnSTD
(Standard)
In this setting, each time you turn on Solo S2, it will
display “Solo S2,” “LASER,” “Ka-band,” “K-band,”
“X-band,” followed by a brief X-band alert. (factory
default) If one or more bands are disabled, (see page
19) a message will appear alerting you if one or more
bands are disabled, (ie. “X OFF”).
PwrOnFST
(Fast power-on)
In this setting, Solo S2 will provide a single X-band
tone if all bands are enabled. If any bands have been
disabled, a double X-band tone and corresponding
message (i.e. “X OFF”), will alert you that one or
more bands have been turned off.
NOTE:
If the batteries need to be replaced, a low-
battery alert will be provided during both power-on
sequences.
Signal Strength Meter
MeterSTD
(Standard meter)
In this setting, the meter displays the band of the
received signal, and a bar graph shows the relative
signal strength. (factory default)
MeterEXP
(Expert Meter)
In this setting, the meter simultaneously tracks
multiple radar signals. It can display up to 2 Ka band,
2 K band, and 4 X band signals at the same time.
NOTE:
The ExpertMeter feature is explained in
more detail on page 13.
AutoMute
aMute ON
(AutoMute on)
In this setting, Solo S2’s audio alerts will initially be at
the volume you set, but after a few seconds, Solo S2
will automatically reduce the volume level, to keep
you informed, but not annoyed. (factory default)
aMuteOFF
(AutoMute off)
With AutoMute off, Solo S2’s audio alerts will remain
at the volume you set for the duration of the radar
encounter.
Audio Tones
Tone STD
(Standard tones)
This setting uses more pleasing tones. (factory
default)
ToneLOUD
(Loud tones)
This setting uses tones that are more piercing. This
setting is recommended for louder vehicles.
