ESCO Technologies ETS-Lindgren EMGen 7003-003 User Manual Download Page 33

Page: 33 / 55

ets-lindgren.com

EMGen Command Set

AM:INT:FREQ:MAX?

Description:

Gets the highest amplitude modulation frequency in Hz.

Syntax:

[:SOURce]:AM:INTernal:FREQuency:MAXimum?

Example:

Write:

AM:INT:FREQ:MAX?

Response:

:AM:INT:FREQ:MAX 100000

AM:INT:FREQ:MIN?

Description:

Gets the lowest amplitude modulation frequency in Hz.

Syntax:

[:SOURce]:AM:INTernal:FREQuency:MINimum?

Example:

Write:

AM:INT:FREQ:MIN?

Response:

AM:INT:FREQ:MIN 10.0

AM:INT:FREQ:STEP

Description:

Sets the step size of the amplitude modulation frequency in Hz. The units default
to Hz but can also be specified as KHZ, MHZ or GHZ.

Syntax:

[:SOURce]:AM:INTernal:FREQuency:STEP <value><unit>

Example:

Write:

AM:INT:FREQ:STEP 10

AM:INT:FREQ:STEP?

Description:

Gets the step size of the amplitude modulation frequency in Hz.

Syntax:

[:SOURce]:AM:INTernal:FREQuency:STEP?

Example:

Write:

AM:INT:FREQ:STEP?

Response:

:AM:INT:FREQ:STEP 10

Summary of Contents for ETS-Lindgren EMGen 7003-003
























































Search results

Summary of Contents for ETS-Lindgren EMGen 7003-003

Reviews:

Related manuals for ETS-Lindgren EMGen 7003-003

Brands by name

Popular brands

ESCO Technologies ETS-Lindgren EMGen 7003-003, User Manual

Search results

Summary of Contents for ETS-Lindgren EMGen 7003-003

Reviews:

Related manuals for ETS-Lindgren EMGen 7003-003

Brands by name

Popular brands