background image

ORDERING SPARE PARTS

ESAB PAPR System

- 19 -

© ESAB AB 2018

ORDERING SPARE PARTS

CAUTION!

Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.

The ESAB PAPR System is designed and manufactured in accordance with the
international and European standard

EN12941:1998+A1:2003+A2:2008

as a

TH2 / + P R

SL

device offering an Assigned Protection Factor of 20 / 50 according to BS4275. Certified

by APAVE SUDEUROPE SAS Notified Body 0082. The ESAB PAPR System can provide
this level of protection when used with filters provided by the manufacturer marked

ESAB

and

EN12941:1998 TH2/3P R SL

. Welding helmets are certified to

EN 175B

. This PPE

device complies with the following applicable EU standards:

EN166B:2001 EN379:2003 +

A1:2009 EN175B

. The ESAB PAPR System is manufactured under

ISO 9001:2000 Quality

System

. On completion of service or repair work, it is the responsibility of the person(s)

performing the work to ensure that the product still complies with the requirements of the
above standards.

Spare parts and wear parts can be ordered through your nearest ESAB dealer, see

esab.com

. When ordering, please state product type, serial number, designation and spare

part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.

Summary of Contents for PAPR System



























Reviews: