Erskine Attachments Cold Planer 18 Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 32

background image

8

MOUNTING INSTRUCTIONS

7. Connect the hydraulic quick couplers from the

attachment to the loader.

IMPORTANT:

Make sure the quick couplers

are fully engaged.  If the quick couplers do not
fully  engage,  check  to  see  that  the  couplers
are the same size and brand.  Do not force the
quick couplers together.

IMPORTANT:

Wipe the ends of the hydraulic

quick couplers (both lead and loader) with a
rag to remove any possible contamination.
Contamination

can

cause

hydraulic

components to fail and is not covered under
warranty.

NOTE:

See the Loader’s Operation and

Maintenance Manual.

NOTE:

Attachment is shipped with 12FJX (1-

1/16” Female JIC Swivel) fittings on the ends
of the lead hoses

8.

Connect the wire harness to the loader’s wire
harness receptacle. (Disregard if a pistol grip
controller is supplied with the attachment.)

Make sure the hoses are properly routed to fit
your  specific  loader.    If  the  hoses  are  not
routed  correctly,  hoses  may  get  pinched  or
rub on tires.  Be sure to check the hose routing
through  the  full  range  of  intended  motion  of
the attachment before operating it.

More  than  one  routing  may  be  acceptable
depending on the loader.  Pick the routing that
best suits your loader.

IMPORTANT:

Proper hose routing is the

responsibility of the owner and/or operator.
Pinched or stretched hoses are not covered
under warranty.

Mounting is now complete and you are ready to
use the attachment. Use the above instructions in
a reverse order to dismount the attachment from
the loader.

14 Pin Wire Harness Connection

CP24 Ready for Operation

«
...
6
7
8
9
10
...
»

Summary of Contents for Cold Planer 18

































Reviews:

No comments

Related manuals for Cold Planer 18

Brand: AVANT Pages: 8

Brand: AVANT Pages: 108

Brand: Grizzly Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands