Erskine Attachments Cold Planer 18 Operator'S Manual Download Page 28 | Manualshive

Page: 28 / 32

background image

28

PROBLEMS

POSSIBLE CAUSE

POSSIBLE SOLUTION

Poor Rotation

Worn pick holders.

Excess material build-up on pick shank.

Holder not properly aligned.

Excessive machine speed.

Replace the worn holders.

Clean holder & shank with solvent.

Remove incorrect holder and reposition.

Slow down the machine.

Excessive Steel

Body Wear

Caused by soft abrasive material.

High rotational speed.

Consider using a larger diameter carbide
tip base.

Consider using a heavier body pick.

Extreme Carbide

Tip Wear

Hard material (aggregate)

Heat build-up on the pick.

Consider using a larger carbide tip.

Consider cooling picks with water.

Tip Fractures

Extremely hard material (aggregate)

Heat build-up on the pick.

Improper pick installation.

Poor rotation.

Consider using a larger carbide tip base
diameter.

Consider cooling picks with water.

Use pick installation tool, rubber mallet, or
copper hammer.

See above instructions.

TROUBLESHOOTING

«
...
26
27
28
29
30
...
»

Summary of Contents for Cold Planer 18

































Reviews:

No comments

Related manuals for Cold Planer 18

Brand: Pitney Bowes Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands