manualshive.com logo in svg

ERMA 2000iN, Owner'S Manual

Share
Download
ERMA 2000iN Owner'S Manual Download Page 37

 

 

33

28

、

Air filter                                                                                                                     

 

It is very important to maintain an air filter in proper condition. 

  Damage to the generator may arise if the filter has: 

• Improperly been serviced (3). 

• Dirt and other foreign elements adhering to the filter 

  due to improper installation and engine wear. 

ALWAYS keep the filter clean at all times.

 

1. Remove the side maintenance cover (5). (Fig.Y). 

2. Remove the air cleaner filter cover by firstly pushing down on the tab on the top of the air cleaner housing (Fig. V). 
Once the air cleaner filter cover tab has been released out of the filter housing, continue to detach the air filter cover 
housing by raising the air filter housing cover up and detaching it form the bottom tab.(Fig.Z). 

3.

 Now that the air filter housing cover has been removed, proceed to remove the air filter by pulling it out towards you. 

4. Wash the air filter in solvent or kerosene and allow to dry. 

5. Lubricate the filter using clean motor oil.   

 

 

 

 

Y 

 

Z 

AIR CLEANER BODY 

AIR CLEANER COVER 

AIR CLEANER COVER SCREW   

AIR CLEANER ELEMENTS 

Summary of Contents for 2000iN













































Reviews:

No comments

Brands by name

Popular brands

Load more brands