background image

2

Introduction

This manual details the proper steps for installing, operating and maintaining  
the Eriez Rota-Grate

®

 and Automated Rota-Grate Magnetic Separator.

Careful attention to these requirements will assure the most efficient  
and dependable performance of this equipment.

If there are any questions or comments about the manual, please  
call Eriez at 814-835-6000 for Rota-Grate assistance.

 

CAUTION ‑ STRONG MAGNET

This equipment includes one or more extremely powerful magnetic circuits. 
The magnetic field may be much stronger than the Earth’s background field 
at a distance several times the largest dimension of the equipment.

• If you use a heart pacemaker or similar device you must never 

approach the equipment because your device may malfunction in  
the magnetic field, with consequences up to and including death.

• To avoid serious pinch‑type injuries caused by objects attracted to the 

magnet, keep all steel and iron objects well away from the equipment. 

Do not allow hands, fingers, and other body parts to be caught between 

the equipment and nearby steel or iron objects.

• Keep credit cards, computer disks, and other magnetic storage 

devices away from the equipment because magnetically stored 
information may be corrupted by the magnetic field.

• Keep electronic devices, such as computers or monitors, away from

 

the equipment because exposure to the magnetic field may result in  
malfunction or permanent damage to such devices.

Contact Eriez if you have a question regarding these precautions.

 CAUTION
Safety labels must be affixed to this product. Should 
the safety label(s) be damaged, dislodged or removed, 
contact Eriez for replacement.

©

 2018 ERIEZ MAGNETICS       ALL RIGHTS RESERVED

Summary of Contents for ROTA-GRATE









Reviews: