manualshive.com logo in svg

Ericsson A1018S, Trouble-Shooting Instruction, Page: 27 / 42

Share
Download
Ericsson A1018S Trouble-Shooting Instruction Download Page 27

A1018s/A1018sc Standard Electrical Repair

4/00021-2/FEA 209 544/16.B

27

(42)

Give the board power and start it.

Measure VVIC at D901:1 (3.2 V, Fig. 7.1).

•

If the voltage is missing:

* Replace C910 and R920 (class A).

•

If the voltage exists:

* Measure the voltage at D901:2 (3.2 V).

* If the voltage exists:

1. Measure the resistance between D901:8 and J603:2 (~33 Ohm).

Incorrect: 1. Replace R600 (class A).

2. Foil damage, the board has to be discarded.

2. Measure the resistance between D901:11 and J603:7 (~33 Ohm).

Incorrect: 1. Replace R628 (class A).

2. Foil damage, the board has to be discarded.

3. Measure the resistance between D901:9 and J603:3 (~ 33 Ohm).

Incorrect: 1. Replace R627 (class A).

2. Foil damage, the board has to be discarded.

4. Measure the resistance between D901:11 and D901:14 (~ 15 kOhm).

Incorrect: 1. Replace R626 (class A).

2. Foil damage, the board has to be discarded.

5. Measure the resistance of C909 (> 1 MOhm).

Incorrect: 1. Replace C909 (class A).

6. Measure the resistance between D901:14 and ground (> 1 MOhm).

Incorrect: 1. Replace C908 (class A).

7. Measure the resistance between D901:14 and J603:1 (~ 0 Ohm).

Incorrect: Foil damage, the board has to be discarded.

8. Replace D901 (class A).

9. Replace R634 (class A).

10. Replace D600 (class B).

* If the voltage is missing at D901:2 (3.2 V):

* Measure the resistance between D901:2 and D600:77 (~0 Ohm)

Correct:

Replace D600 (class B).

Incorrect: Foil damage, the board has to be discarded.

If the fault still remains, send the phone to the next repair level.

Summary of Contents for A1018S











































Reviews:

No comments