Ergotron WorkFit B, User Manual, Page: 6 / 19

6 of 19
888-24-227-G-01 rev. E • 12/19
A B C
1
2
3
4
1x
1x
3x
2x
1x
1x
1/4”
1 4 mm
# 12 , Ø 0.19 ” ( 4 .8mm)
#4 6 , Ø 0.081 ” (2mm)
2x
2.126 2.126
12.992
5.118
X
X
3.900
35.197
DIMENSIONS ARE IN INCHES
W ORKS U RFACE TEMPLATE FOR W ORKFIT-B , HD
La y this template on the b ottom of y our worksurface
to drill the holes to attach the W orkFit-D , Base.
Back of Base Bracket
Brake Release
Use Drill Bit #21,
Ø 0.19” (4.8 mm)
to drill these 9 holes
0.375” (9.5 mm) deep.
Use Drill Bit #21,
Ø 0.19” (4.8 mm)
to drill these 8 holes
0.375” (9.5 mm) deep.
Use Drill Bit #46,
Ø 0.081” (2mm)
to drill these 3 holes
0.24” (6 mm) deep.
Center Point of Base Brackets
Depth of
W orksurface
TIPPI NG HAZARD !
Center W orksurface from Side-to-Side Across Base Brackets .
Failure to follow these instructions ma y make this product unsta b le
and ma y result in e q uipment damage and/or personal in j ur y.
823-558-00 rev.A 05/13
23.50 - 24.25”----0.25”
24.25 - 25.00”----0.75”
25.00 - 25.75”----1.25”
25.75 - 26.50”----1.75”
26.50 - 27.25”----2.25”
27.25 - 28.00”----2.75”
28.00 - 28.75”----3.25”
28.75 - 29.50”----3.75”
29.50 - 30.25”----4.25”
X
Depth of
W orksurface
597 - 616 mm ---6 mm
616 - 635 mm ---19 mm
635 - 654 mm ---32 mm
654 - 673 mm ---44 mm
673 - 692 mm ---57 mm
692 - 711 mm ---70 mm
711 - 730 mm ---83 mm
730 - 749 mm ---95 mm
749 - 768 mm ---108 mm
4.25” (108 mm)
3.75” (95 mm)
3.25” (83 mm)
2.75” (70 mm)
2.25” (57 mm)
1.75” (44 mm)
1.25” (32 mm)
0.75” (19 mm)
0.25” (6 mm)
Align REAR Edge of Worksurface X distance
from the back of the Base Brackets.
See table for value of
X based on the depth of
your worksurface.
4.25” (108 mm)
3.75” (95 mm)
3.25” (83 mm)
2.75” (70 mm)
2.25” (57 mm)
1.75” (44 mm)
1.25” (32 mm)
0.75” (19 mm)
0.25” (6 mm)
M2.9 x 8mm
ST3.9 x 16mm
M5 x 6mm
17x
16x
3x
4 x
#12-14 x 5/8”
C omponen t s
T oo l s N eeded