Ercogener GenLoc 41e User Manual Download

Page: 7 / 71

EG_GenLoc41e_1055_UG_003_UK

Page 7 / 71

Descriptions and non-contractual illustrations in this document are given as an indication only.

ERCOGENER reserves the right to make any modifications.

Dct_427_02

Warning

The

GenLoc 41e

is dedicated to '

Machine To Machine

' (M2M) applications only.

ERCOGENER

recommends the use of SIM card subscriptions of the

'Machine To Machine

(M2M) type.
Video, VoIP (Voice over IP) transfer requires the payment of additional royalties.



ERCOGENER

advises to read carefully all the documents concerning the

GenLoc 41e

(User Guide,

Application Notes, Command List

)

that can be download on our website www.ercogener.com



ERCOGENER

cannot be held responsible for:

The problems due to an inappropriate use of the

GenLoc 41e

The problems due to a wrong configuration

The problems due to a wrong use of an embedded software application developed or
supplied by a third party.

Dysfunctions due to the absence or a bad coverage or

termination

of the GSM, GPRS and

GPS networks.

The dysfunctions if the product is used for the watching of physical persons where human
life is engaged.



ERCOGENER

reserves the right to modify the functions of its products "

GenLoc 41e

" and

"EaseLoc" without previous notice.

- In order to avoid any risk of electrocution, do not open the casing.

- For any functioning, the casing must be closed.

- No internal part can be repaired by the user. The

GenLoc 41e

must be returned to the factory for any repair

the RMA request (Return Material Authorization).

- The

GenLoc 41e

must be placed in a normally ventilated area, out of sources of heat.

- In order to guarantee the electromagnetic compatibility, the length of the serial cable, the supply cable and

the inputs/outputs cable must not exceed 3 meters.

- The

GenLoc 41e

must not be connected directly to the mains supply; a voltage adapter must be used.

This marking on the product, accessories, packaging or literature indicates that the product
and its electronic accessories (e.g. cable etc.) should not be disposed of with other household
waste.

Summary of Contents for GenLoc 41e








































































Search results

Summary of Contents for GenLoc 41e

Reviews:

Related manuals for GenLoc 41e

Brands by name

Popular brands

Ercogener GenLoc 41e, User Manual

Search results

Summary of Contents for GenLoc 41e

Reviews:

Related manuals for GenLoc 41e

Brands by name

Popular brands