manualshive.com logo in svg

Ercogener 4408100066, User Manual, Page: 7 / 51

Share
Download
Ercogener 4408100066 User Manual Download Page 7

 

EG_GenPro425e_1103_UG_001_UK.docx

 

Page 7 / 51 

 

Descriptions and non-contractual illustrations in this document are given as an indication only. 

ercogener reserves the right to make any modifications. 

Dct_427_02

 

Warning 

 

 

The 

GenPro

 

425e

 is dedicated to '

Machine To Machine

' (M2M) applications only. 

ercogener

  recommends  the  use  of  SIM  card  subscriptions  of  the 

'Machine  To  Machine

' 

(M2M) type.  

 

 

ercogener

  recommends  to  read  carefully  all  documents  linked  to  the  product 

GenPro 425e

  (User 

Guide, Application Notes, Command List) that can be download on our website 

www.ercogener.com

. 

 

ercogener

 cannot be held responsible for: 

- The problems due to an inappropriate use of the 

GenPro 425e

. 

- The problems due to a wrong configuration. 

- The problems due to a wrong use of an embedded software application developed or supplied by a 

third party. 

- The dysfunctions due to the absence, a bad coverage or termination of the GSM, GPRS, UMTS and 

LTE networks services. 

- The  dysfunctions  if  the  product  is  used  for  the  watching  of  physical  persons  where  human  life  is 

engaged. 

 

ercogener

 reserves the right to modify the functions of its products "

GenPro 425e

 " and "

EasePro

", 

"

EaseIP

", "

EaseNTRIP

" without previous notice.  

 

- To avoid any risk of electrocution, do not open the casing. 

- For any functioning, the casing must be closed. 

-  No  internal  part  can  be  repaired  by  the  user.  The 

GenPro 425e

  must  be  returned  to  the  factory  for  any 

repair with RMA request (Return Material Authorization). 

- The 

GenPro 425e

 must be placed in a normally ventilated area, out of sources of heat. 

-  In  order  to  guarantee  the  electromagnetic  compatibility,  the  length  of  the  serial  cable,  the  power  supply 

cable and the inputs/outputs cable must not exceed 3 meters. 

- The 

GenPro 425e

 must not be connected directly to the mains supply (230 V

AC

). A PS1 (max 15W) voltage 

adapter must be used. 

 

 

 

This  marking  on  the  product,  accessories,  packaging  or  literature  indicates  that  the  product 
and its electronic accessories (e.g. cable etc.) should not be disposed of with other household 
waste. 

 

Summary of Contents for 4408100066




















































Reviews:

No comments