manualshive.com logo in svg

Ercogener 4408100066, User Manual, Page: 31 / 51

Share
Download
Ercogener 4408100066 User Manual Download Page 31

 

EG_GenPro425e_1103_UG_001_UK.docx

 

Page 31 / 51 

 

Descriptions and non-contractual illustrations in this document are given as an indication only. 

ercogener reserves the right to make any modifications. 

Dct_427_02

 

Figure 15 : Internal electric scheme of opto-coupled inputs 

 

 

 

The minimum command voltage for the detection is: 

3.5 V

 

 

 

The maximum command voltage is: 

35 V

 

 

 

3.9.1.1 

Inputs functioning 

This function can also be controlled with AT commands:  

AT+GPIOGET

 This command is used to read the inputs. The reading is done with the following format: 

 

AT+GPIOGET=<n> 

with: 

 

<n>

 = 7 : reading input 1  

 

 

 8 : reading input 2 

 

 

 9 : reading input 3 

Examples: 

Command 

Response 

Interpretation 

AT+GPIOGET=7 

+GPIOGET: 7= 0 
 
OK 

Input 1 read at 0, command voltage > 3.5V on 
input 1 

AT+GPIOGET=9

 

+GPIOGET: 9= 1 
 
OK 

Input 3 read at 1,  the input 3 is connected to 
GND 

 

 

Summary of Contents for 4408100066




















































Reviews:

No comments