background image

18

Operators Manual ES-650PIA

Suction Trunk

Butterfly 

Screw

Fastening 

Collar

Wing Nuts

Installing the suction hose (Accessory)

• 

Make sure that the engine is switched off (set the stop 

switch  to  “Off”)  and  disconnect  the  spark  plug  con

-

nector. Move the suction trunk to the highest position. 

Remove the suction trunk from the unit by removing 

the two wing nuts and the butterfly screw on the safety 

switch.

• 

Attach the mounting flange of the suction trunk to the 

turbine casing accordingly. Slide the suction hose onto 

the mounting flange and tighten the hose clamp.

• 

Always switch off the engine and remove the spark 

plug connector to change between the suction hose 

and the suction trunk.

DANGER:

Never locate or bridge the safety switch on the 

turbine housing.

Replace defective switch before putting it into 

operation again. Never start or run the engine 

without the suction trunk or suction hose.

Risk of serious injuries. 

Clothes and limbs could be sucked in.

In case of contamination/clogging

To do this, remove the two outer wing nuts and unscrew 

the butterfly screw in the middle, on the safety switch, 

completely. Now remove the mounting collar for the 

suction trunk and the suction trunk.
Loosen the dirt / blockage with a wooden stick or simi-

lar. Do not reach into the turbine housing with your bare 

hands, always use gloves.
Once all coarse dirt has been removed and the turbine 

can be turned freely again, reinstall the suction trunk and 

let the unit run. It is now ready for use again.

Pay Attention:

Regular inspection and cleaning of the turbine housing 

maintains the high suction power of the machine.

Suction Hose

Mounting Flange

Wing Nuts

Butterfly Screw

Suction Hose

mounted

Summary of Contents for ES-650PIA

























Reviews: