manualshive.com logo in svg

Eramco Dust Free 3000 Series, Installation And Service Manual

Share
Download
Eramco Dust Free 3000 Series Installation And Service Manual Download Page 10

REPLACEMENT PARTS LIST

7

Hogs hair washable pre-filter (Set of 2).

6" 30/40% pleated pre-filter (Box of 4).

Spark arresting pre-filter, metal mesh (Set of 2).

Disposable synthetic fiber pre-filter (Box of 12).

Oil impinger pre-filter (Set of 2).

30/40% Duo Cube particle filter (Set of 2).

65% Ashrae deep pocket V-bag (Set of 2).

65% Ashrae short pocket V-bag (Set of 2) used with sorbent panels.

95% Ashrae deep pocket V-bag (Set of 2).

95% Ashrae short pocket V-bag (Set of 2) used with sorbent panels.

98% D.O.P. LW bank (Set of 2).

Refillable sorbent media panel, empty (1).

120 lbs. bulk Charcoal for refill.

150 lbs. bulk Permanganate for refill.

5 HP blower motor.

7.5 HP blower motor.

Drive belt.

95% D.O.P. mini-pleat (Set of 2).

99.97% D.O.P. Hepa (Set of 2).

5" w.g. Magnahelic gauge.

50 ft. tubing for Magnahelic gauge.

Ozone generator grid plate (1).

24V remote on/off switch assembly (no starter).

UV replacement lamp (Set of 2).

Particle ionizer probe (entire assembly).

Blower shaft bearings (Set of 2).

Part No.

Description

PRE-FILTER

ADSORBENT FILTER

MAIN FILTER

FINAL FILTER

Summary of Contents for Dust Free 3000 Series











Reviews:

No comments

Brands by name

Popular brands

Load more brands