background image

 

                     

1. Safety Instruction 

 

 

 

 

 

WARNING

 

 

P

lease keep this User Guide for future consultation. If you sell the unit to another 

user be sure that they also receive this. 

Unpack and check carefully that there is no transportation damage before using the 
unit. 

Ÿ

 

Before  operating,  ensure  that  the  voltage  and  frequency  of  the  power  supply 
match the power requirements of the unit.   

Ÿ

 

It’s important to ground the yellow/green conductor to earth in order to avoid 
electric shock. 

Ÿ

 

The unit is for indoor use only. Use only in a dry location. 

Ÿ

 

The unit must be installed in a location with adequate ventilation, at least 50cm 
from adjacent surfaces. Be sure that no ventilation slots are blocked.   

Ÿ

 

Disconnect the mains power before replacement or servicing.   

Ÿ

 

Make sure there are no flammable materials close to the unit while operating as 
they may cause a fire hazard.   

Ÿ

 

Always use a safety cable when installing this unit. Do not carry the unit by its 
head only, always carry it using the base.     

Ÿ

 

The maximum ambient temperature is to: 40 degrees C. Don’t operate it where 
the temperature is higher than this. 

Ÿ

 

In  the  event  of  a  serious  operating  problem  stop  using  the  unit  immediately. 
Never try to repair the unit by yourself. Repairs carried out by unskilled people 
can  lead  to  damage  or  malfunction.  Please  contact  the  nearest  authorized 
technical assistance center. Always use the same type spare parts. 

Ÿ

 

Do not touch any power cables during operation as the high voltage may cause an 
electric shock. 

Warning 

Ÿ

 

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to 
rain or moisture. 

    Do not open the unit within five minutes after switching off. 

Ÿ

 

The housing and lenses must be replaced if they are visibly damaged. 

Installation 

The unit should be mounted via its screw holes onto the bracket. Always ensure 

that the unit is firmly fixed to avoid vibration and slipping while operating. Make 

sure that the structure to which you are attaching the unit to is secure and is able 

to support a weight of 10 times of the unit’s weight. Always use a safety cable that 

can hold 12 times of the weight of the unit when installing the fixture.   

The equipment must be installed by professionals and it must be installed in a 

place where is out of the reach of people and no one can pass by or under it. 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Please read the instructions carefully as they include important 

information about installation, usage and maintenance. 

Summary of Contents for Triclops Beam








Reviews: