Epson SureColor SC-F9330 Series User Manual Download Page 83

Page: 83 / 145

Cleaning the Heat Shield

When it becomes hard to see inside the ink tank because
ink has adhered to the heat shield, remove the heat
shield and clean it.

A Philips head screwdriver is required for the following
work. Make sure to have one prepared before you start
working.

Before starting this procedure, be sure to read the
following:

“Precautions regarding maintenance” on page 59

Remove the heat shield.

Completely loosen the four screws that hold the
heat shield in place to remove the heat shield.

Soak a soft cloth in water, wring it out
thoroughly, and then wipe off any ink that has
adhered to the heat shield.

Install the heat shield.

Align the heat shield's holes with those in the ink
tank holder and tightly screw in the screws.

Applying Grease to the
Carriage Rod

When

Apply secondary carriage rod grease. See

manual.

is displayed on the control panel screen, follow

the steps below to apply grease to the carriage rod as
soon as possible.

Location of Carriage Rod and
Used Pad

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SureColor SC-F9330 Series


















































































































































Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands

Epson SureColor SC-F9330 Series, User Manual

Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands