manualshive.com logo in svg

Epson SureColor SC-F9330 Series, User Manual

Share
Download
Epson SureColor SC-F9330 Series User Manual Download Page 66

See steps 2 to 6 in “Procedure for Ink Refills” for the
procedure to replace chip units.

U

 

“Procedure for Ink Refills” on page 66

You can confirm whether or not a chip unit is reserved
by looking at the chip unit's status icon.

U

 

“Understanding the Display” on page 14

Precautions when refilling ink

Read the Safety Data Sheet before performing the
procedure.

You can download it at your local Epson Web site.

Caution:

Note the following points when refilling ink.

❏

Gently tear off the ink pack spout opening.
If you cut the nozzle too quickly, ink may
splatter.

❏

Do not squeeze open ink packs. Ink may
spill.

❏

Gently tilt the ink pack when pouring ink
into the ink tank.

c

Important:

❏

Epson recommends the use of genuine Epson
ink packs.
Epson cannot guarantee the quality or
reliability of nongenuine ink. The use of
non-genuine ink may cause damage that is not
covered by Epson’s warranties, and under
certain circumstances, may cause erratic
printer behavior.
Information about non-genuine chip unit
status may not be displayed, and use of
non-genuine ink is recorded for possible use in
service support.

❏

Genuine Epson ink, other than those specified
here, could cause damage that is not covered by
Epson’s warranties.

U

 

“Options and Consumable Products” on

page 116

❏

Do not place items on the ink tank or subject the
ink tank to strong impacts. The ink tank could
become detached.
Contact your dealer or Epson Support.

Procedure for Ink Refills

A

If the 

Check Ink Levels

 message is displayed on

the control panel screen, check the ink level in the
ink tank by using the scale on the ink pack.

SC-F9300 Series     User's Guide

Maintenance

 

66

Summary of Contents for SureColor SC-F9330 Series


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands