manualshive.com logo in svg

Epson SureColor P-Series, Setup Manual

Share
Download
Epson SureColor P-Series Setup Manual Download Page 32

Installing the software

|

31

Installing the software

Download and run your product’s software package:

•

www.epson.com/support/p10000 

(U.S.) or 

www.epson.ca/support/p10000

 (Canada)

•

www.epson.com/support/p20000

 (U.S.) or 

www.epson.ca/support/p20000 

(Canada)

Follow the instructions on the screen to run the setup program. 

Updating your printer firmware

To keep your printer features and functionality up to date, you should periodically check for a new version 
of firmware on the Epson support site and update your printer, if necessary.

Checking the current firmware version

1.

Press the 

Menu 

button.

2.

Press the 

d 

button until 

Setup 

is highlighted, then press 

OK.

3.

Press the 

d 

button until 

Printer Status 

is highlighted, then press 

OK

.

4.

Press the 

d 

button again until 

Firmware Version 

is displayed, then press 

OK

. Note the firmware 

version displayed. When finished, press the 

y

 

back button.

Updating the firmware

Before updating your printer’s firmware, make sure your printer is turned on, connected to your computer 
or network, and that the LCD screen shows the READY status.

1.

Visit the support page for your product:

•

www.epson.com/support/p10000 

(U.S.) or 

www.epson.ca/support/p10000

 (Canada)

•

www.epson.com/support/p20000

 (U.S.) or 

www.epson.ca/support/p20000 

(Canada)

2.

Click 

Drivers & Downloads

.

3.

Click 

Firmware

.

4.

Click 

Download

.

Summary of Contents for SureColor P-Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands