Epson Stylus Pro 9000 Printer Manual Download Page 104 | Manualshive

Page: 104 / 165

background image

B-3

Using EPSON Drivers and Utilities for Macintosh

|

B-3

3. Connect one end of the interface cable to the serial connector on the

back of the printer.

4. Connect the other end of the interface cable to either the modem port or

printer port on the Macintosh. (Some Macintosh PowerBook

®

models

have only one serial port.)

5. Turn on the printer by pressing the

Power

button.

6. Turn on your Macintosh.

See the next section for instructions on installing the printer software. You
must install the printer software before using your printer.

Setting Up Your Software

You need to install the drivers and utilities on any Macintosh that will print
to the EPSON Stylus Pro 9000 or 9500. Make sure each Macintosh meets
the minimum system requirements. Then follow the procedure for installing
the software. Depending on your network configuration, you may also want
to set up printer sharing if you have the EPSON Stylus Pro 9500.

Note

If your Macintosh has a
built-in modem, connect
the interface cable to the
printer port.

«
...
102
103
104
105
106
...
»

Summary of Contents for Stylus Pro 9000






































































































































































Reviews:

No comments

Related manuals for Stylus Pro 9000

Brand: NCR Pages: 10

IR5000 - iR B/W Laser

Brand: Canon Pages: 86

ExpressCard 2000

Brand: Magtek Pages: 25

Brand: Xerox Pages: 262

Brand: QuickLabel Systems Pages: 122

Brand: Lexmark Pages: 9

Brand: Parkside Pages: 176

Brand: Evolis Pages: 63

Brand: Lexmark Pages: 8

Brand: Oki Pages: 18

Monochrome Laser

Brand: Lexmark Pages: 1

Brand: Protech Systems Pages: 140

Brand: Xerox Pages: 109

Brand: Paradise POS Pages: 275

THERMOMARK CARD

Brand: Phoenix Contact Pages: 35

Brand: Oki Pages: 138

Brand: Xerox Pages: 4

WORKCENTRE 7428

Brand: Xerox Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands