Epson Stylus Pro 9000 Printer Manual Download Page 100

Page: 100 / 165

A-3

Installing an Interface Card

A-3

5. Secure the interface card in the slot with the two screws included with

the card.

6. Make sure the printer has been turned off using the

Power

button.

Then plug in the power cord.

7. To initialize the EpsonNet Internal Print Server, turn on the printer

while holding down the status sheet button on the card for about
5 seconds.

8. Connect the appropriate cable to the card and to your network hub or

computer.

To remove an interface card, turn off the printer, unplug the power cord,
and follow the above steps in reverse order.

Before you can use the EpsonNet Internal Print Server, you must configure
it for your network protocols and operating system. See the

EpsonNet

Internal Print Server Administrator’s Manual

for instructions.

Before you can print, you must install the printer software, as described on
page B-3 (Macintosh) or page C-2 (Windows).

Summary of Contents for Stylus Pro 9000






































































































































































Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands

Epson Stylus Pro 9000, Printer Manual

Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands