Epson SC-F9300 series User Manual Download Page 95

Page: 95 / 146

Item

Parameter

Explanation

Manual Reset

When the

button is pressed, the value for print length returns to 0.

Auto Reset

Off

Select either

Off

(do not automatically reset the value for print length)

Per Job

(reset when starting to print the next job).

When

Off

is selected, the value does not reset until you do

Manual

Reset

. However, once the value reaches 9999, it automatically resets

and returns to 0.

When

Per Job

is selected, the value returns to 0 when printing starts for

the next job so you can check the print length per job. You can also
check how far along the print job is while printing.

Per Job

Customize Settings

Current Settings

To change the currently selected setting, select

Current Settings

When changing specific media settings, select the setting number for
the target media.

See the following table for details on the setting content.

“Media Setting Item” on page 95

1 to 30 (media setting number) XXXXXXXXXXX
(displays name of registered custom paper)

Select Media

1 to 30 (media setting number) XXXXXXXXXXX
(displays name of registered custom paper)

Choose the media settings used for printing.

To register new settings, either do

Easy Media Setup

or register the

media settings on the printer using the supplied Epson Control
Dashboard.

“Saving New Media Settings” on page 45

Change setting content in

Customize Settings

Media Setting Item

The optimal media setting values are set if you either do

Easy Media Setup

or register the media settings on the

printer using the supplied Epson Control Dashboard. Normally, use this as it is. When using specific media or
when a problem such as head striking or banding is detected in printing results, change the default.

The default settings for each of the following items differ depending on the content set in

Media Type

. See the

following for details on the default settings for each media type.

“Media Settings List for Each Media Type” on page 129

Item

Parameter

Explanation

Setting Name

Assign the media setting bank a name up to 22 half-size characters
long. Using distinctive names makes it easier to select banks for use.

SC-F9300 Series User's Guide

Using the Control Panel Menu

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands