Epson SC-F9300 series User Manual Download Page 66 | Manualshive

Page: 66 / 146

background image

However, when reservation is done, a warning is not
displayed when the estimated amount of ink becomes
low. Refill the ink with one pack of ink if the
remaining ink is 70 mm or less from the bottom of the
ink tank.

See steps 2 to 6 in “Procedure for Ink Refills” for the
procedure to replace chip units.

U

“Procedure for Ink Refills” on page 66

You can confirm whether or not a chip unit is
reserved by looking at the chip unit's status icon.

U

“Understanding the Display” on page 14

Precautions when refilling ink

Read the Safety Data Sheet before performing the
procedure.

You can download it at your local Epson Web site.

Caution:

Note the following points when refilling ink.

❏

Gently tear off the ink pack spout opening.
If you cut the nozzle too quickly, ink may
splatter.

❏

Do not squeeze open ink packs. Ink may
spill.

❏

Gently tilt the ink pack when pouring ink
into the ink tank.

c

Important:

❏

Epson recommends the use of genuine Epson
ink packs.
Epson cannot guarantee the quality or
reliability of nongenuine ink. The use of
non-genuine ink may cause damage that is
not covered by Epson’s warranties, and under
certain circumstances, may cause erratic
printer behavior.
Information about non-genuine chip unit
status may not be displayed, and use of
non-genuine ink is recorded for possible use
in service support.

❏

Genuine Epson ink, other than those specified
here, could cause damage that is not covered
by Epson’s warranties.

U

“Options and Consumable Products” on

❏

Do not place items on the ink tank or subject
the ink tank to strong impacts. The ink tank
could become detached.
Contact your dealer or Epson Support.

Procedure for Ink Refills

A

If the

Check Ink Levels

message is displayed on

the control panel screen, check the ink level in
the ink tank by using the scale on the ink pack.

SC-F9300 Series User's Guide

Maintenance

66

«
...
64
65
66
67
68
...
»

Summary of Contents for SC-F9300 series



















































































































































Reviews:

No comments

Related manuals for SC-F9300 series

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: A.MENARINI Pages: 2

Brand: R.M. Young Pages: 10

Brand: J.P. SELECTA Pages: 32

Synthesis SDEC-3000

Brand: JBL Pages: 24

Brand: Xilica Audio Design Pages: 30

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 64

Brand: M-Audio Pages: 16

Brand: M-Audio Pages: 4

Brand: M-Audio Pages: 52

Brand: NAMYSLO Pages: 13

Brand: Life Fitness Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands