manualshive.com logo in svg

Epson S1C88650, Technical Manual

Share
Download
Epson S1C88650 Technical Manual Download Page 99

S1C88650 TECHNICAL MANUAL

EPSON

91

5  PERIPHERAL CIRCUITS AND THEIR OPERATION (Programmable Timer)

5.10.5 Interrupt function

The 16-bit programmable timer can generate an
interrupt with the compare match signal and
underflow signal of each timer.
Figure 5.10.5.1 shows the configuration of the 16-
bit programmable timer interrupt circuit.

The compare match signal and underflow signal of
each timer set the corresponding interrupt factor
flag to "1". At that point, the interrupt is generated.
The interrupt can also be prohibited by setting the
interrupt enable register to correspond with the
interrupt factor flag.
Furthermore, the priority level of the interrupt for
the CPU can be set to an optional level (0–3) using
the interrupt priority register.
Table 5.10.5.1 shows the interrupt factor flags,
interrupt enable registers and interrupt priority
registers corresponding to the interrupt factors.

In the 8-bit mode, the compare match interrupt
factor flag and underflow interrupt factor flag are
individually set to "1" by the timers.

In the 16-bit mode, the interrupt factor flags of
Timer(H) are set to "1" by the compare match and
underflow in 16 bits.

Refer to Section 5.14, "Interrupt and Standby
Status", for details of the interrupt control registers
and operations subsequent to interrupt generation.

The exception processing vector addresses for the 16-
bit programmable timer interrupt are set as follows:

Timer 0 underflow interrupt:

000016H

Timer 0 compare match interrupt: 000018H
Timer 1 underflow interrupt:

00001AH

Timer 1 compare match interrupt: 00001CH
Timer 2 underflow interrupt:

00001EH

Timer 2 compare match interrupt: 000020H
Timer 3 underflow interrupt:

000022H

Timer 3 compare match interrupt: 000024H
Timer 4 underflow interrupt:

00003CH

Timer 4 compare match interrupt: 00003EH
Timer 5 underflow interrupt:

000040H

Timer 5 compare match interrupt: 000042H
Timer 6 underflow interrupt:

000044H

Timer 6 compare match interrupt: 000046H
Timer 7 underflow interrupt:

000048H

Timer 7 compare match interrupt: 00004AH

Table 5.10.5.1  Interrupt control registers

Timer 0

Timer 1

Timer 2

Timer 3

Timer 4

Timer 5

Timer 6

Timer 7

Interrupt factor

Interrupt factor flag

Counter underflow
Compare match
Counter underflow
Compare match
Counter underflow
Compare match
Counter underflow
Compare match
Counter underflow
Compare match
Counter underflow
Compare match
Counter underflow
Compare match
Counter underflow
Compare match

Name

FTU0
FTC0
FTU1
FTC1
FTU2
FTC2
FTU3
FTC3
FTU4
FTC4
FTU5
FTC5
FTU6
FTC6
FTU7
FTC7

Address·Dx

00FF29H·D0
00FF29H·D1
00FF29H·D2
00FF29H·D3
00FF29H·D4
00FF29H·D5
00FF29H·D6
00FF29H·D7
00FF2EH·D0
00FF2EH·D1
00FF2EH·D2
00FF2EH·D3
00FF2EH·D4
00FF2EH·D5
00FF2EH·D6
00FF2EH·D7

Interrupt enable register

Name

ETU0
ETC0
ETU1
ETC1
ETU2
ETC2
ETU3
ETC3
ETU4
ETC4
ETU5
ETC5
ETU6
ETC6
ETU7
ETC7

Address·Dx

00FF25H·D0
00FF25H·D1
00FF25H·D2
00FF25H·D3
00FF25H·D4
00FF25H·D5
00FF25H·D6
00FF25H·D7
00FF2CH·D0
00FF2CH·D1
00FF2CH·D2
00FF2CH·D3
00FF2CH·D4
00FF2CH·D5
00FF2CH·D6
00FF2CH·D7

Interrupt priority register

Name

PPT0
PPT1

PPT2
PPT3

PPT4
PPT5

PPT6
PPT7

Address·Dx

00FF21H·D2
00FF21H·D3

00FF21H·D4
00FF21H·D5

00FF2AH·D0
00FF2AH·D1

00FF2AH·D2
00FF2AH·D3

Summary of Contents for S1C88650























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands