Epson S1C17M20 Technical Manual Download Page 73

Page: 73 / 319

6 I/O PORTS (PPORT)

S1C17M20/M21/M22/M23/M24/M25

Seiko Epson Corporation

6-9

TECHNICAL MANUAL (Rev. 1.0)

Bits 15–8 P

EDGE[7:0]

These bits select the input signal edge to generate a port input interrupt.

1 (R/W): An interrupt will occur at a falling edge.

0 (R/W): An interrupt will occur at a rising edge.

Bits 7–0

IE[7:0]

These bits enable port input interrupts.

1 (R/W): Enable interrupts

0 (R/W): Disable interrupts

Note: To prevent generating unnecessary interrupts, the corresponding interrupt flag should be cleared

before enabling interrupts.

Port Chattering Filter Enable Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

PxCHATEN

15–8 –

0x00

–

7–0 PxCHATEN[7:0]

0x00

R/W

1: The bit configuration differs depending on the port group.

Bits 15–8 Reserved

Bits 7–0

CHATEN[7:0]

These bits enable/disable the chattering filter function.

1 (R/W): Enable (The chattering filter is used.)

0 (R/W): Disable (The chattering filter is bypassed.)

Port Mode Select Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

PxMODSEL

15–8 –

0x00

–

7–0 PxSEL[7:0]

0x00

R/W

1: The bit configuration differs depending on the port group.

2: The initial value may be changed by the port.

Bits 15–8 Reserved

Bits 7–0

SEL[7:0]

These bits select whether each port is used for the GPIO function or a peripheral I/O function.

1 (R/W): Use peripheral I/O function

0 (R/W): Use GPIO function

Port Function Select Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

PxFNCSEL

15–14 Px7MUX[1:0]

0x0

R/W –

13–12 Px6MUX[1:0]

0x0

R/W

11–10 Px5MUX[1:0]

0x0

R/W

9–8 Px4MUX[1:0]

0x0

R/W

7–6 Px3MUX[1:0]

0x0

R/W

5–4 Px2MUX[1:0]

0x0

R/W

3–2 Px1MUX[1:0]

0x0

R/W

1–0 Px0MUX[1:0]

0x0

R/W

1: The bit configuration differs depending on the port group.

2: The initial value may be changed by the port.

Bits 15–14 P

7MUX[1:0]

Bits 1–0

0MUX[1:0]

These bits select the peripheral I/O function to be assigned to each port pin.

Summary of Contents for S1C17M20
































































































































































































































































































































Search results

Summary of Contents for S1C17M20

Reviews:

Brands by name

Popular brands

Epson S1C17M20, Technical Manual

Search results

Summary of Contents for S1C17M20

Reviews:

Brands by name

Popular brands