manualshive.com logo in svg

Epson S1C17M12, Technical Manual, Page: 64 / 253

Share
Download
Epson S1C17M12 Technical Manual Download Page 64

6  I/O PORTS (PPORT)

6-8

 

Seiko Epson Corporation 

S1C17M12/M13 TECHNICAL MANUAL

 

 

(Rev. 1.2)

Bits 15–8  P

x

PDPU[7:0]

 

These bits select either the pull-up resistor or the pull-down resistor when using a resistor built into 

the port.

 

1 (R/W):  Pull-up resistor

 

0 (R/W):  Pull-down resistor

 

The selected pull-up/down resistor is enabled when the P

x

RCTL.P

x

REN

y

 bit = 1.

Bits 7–0 

P

x

REN[7:0]

 

These bits enable/disable the port pull-up/down control.

 

1 (R/W):  Enable (The built-in pull-up/down resistor is used.)

 

0 (R/W):  Disable (No pull-up/down control is performed.)

 

Enabling this function pulls up or down the port when output is disabled (P

x

IOEN.P

x

OEN

y

 bit = 0). 

When output is enabled (P

x

IOEN.P

x

OEN

y

 bit = 1), the P

x

RCTL.P

x

REN

y

 bit setting is ineffective re-

gardless of how the P

x

IOEN.P

x

IEN

y

 bit is set and the port is not pulled up/down.

 

These bits do not affect the pull-up/down control when the port is used as a peripheral I/O function.

P

x

 Port Interrupt Flag Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

PxINTF

15–8 –

0x00

–

R

–

7–0 PxIF[7:0]

0x00

H0

R/W Cleared by writing 1.

*

1:  This register is effective when the GPIO function is selected.

*

2:  The bit configuration differs depending on the port group.

Bits 15–8  Reserved

Bits 7–0 

P

x

IF[7:0]

 

These bits indicate the port input interrupt cause occurrence status.

 

1 (R): 

Cause of interrupt occurred

 

0 (R): 

No cause of interrupt occurred

 

1 (W): 

Clear flag

 

0 (W): 

Ineffective

P

x

 Port Interrupt Control Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

PxINTCTL

15–8 PxEDGE[7:0]

0x00

H0

R/W –

7–0 PxIE[7:0]

0x00

H0

R/W

*

1:  This register is effective when the GPIO function is selected.

*

2:  The bit configuration differs depending on the port group.

Bits 15–8  P

x

EDGE[7:0]

 

These bits select the input signal edge to generate a port input interrupt.

 

1 (R/W):  An interrupt will occur at a falling edge.

 

0 (R/W):  An interrupt will occur at a rising edge.

Bits 7–0 

P

x

IE[7:0]

 

These bits enable port input interrupts.

 

1 (R/W):  Enable interrupts

 

0 (R/W):  Disable interrupts

Note:  To prevent generating unnecessary interrupts, the corresponding interrupt flag should be cleared 

before enabling interrupts.

P

x

 Port Chattering Filter Enable Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

PxCHATEN

15–8 –

0x00

–

R

–

7–0 PxCHATEN[7:0]

0x00

H0

R/W

*

1:  The bit configuration differs depending on the port group.

Summary of Contents for S1C17M12






























































































































































































































































Reviews:

No comments