manualshive.com logo in svg

Epson LQ-2180, Service Manual, Page: 2 / 56

Share
Download
Epson LQ-2180 Service Manual Download Page 2

Notice:

„

All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, 
electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.

„

The contents of this manual are subject to change without notice.

„

All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON 
would greatly appreciate being informed of them.

„

The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences 
thereof.

EPSON is a registered trademark of SEIKO EPSON CORPORATION.

General Notice:

Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their 
respective owners. EPSON disclaims any and all rights in those marks.

Copyright © 1996 SEIKO EPSON CORPORATION. Printed in Japan.

http://www.4008109977.com     guangzhou epson  service :020-84207330 

Summary of Contents for LQ-2180

























































Reviews:

No comments