manualshive.com logo in svg

Epson EMP 9000 - SXGA LCD Projector, Owner'S Manual

Share
Download
Epson EMP 9000 - SXGA LCD Projector Owner'S Manual Download Page 84

Menu Options

■  ■  ■  ■  ■  ■

63

About Menu

The About menu displays the following information about 
your projector.

Image source = Computer or Component Video

Image source = Video

Menu item

Description

Lamp

Displays the number of hours the current lamp has 
been used. The lamp light turns red when the projector 
lamp is near the end of its normal life. When this 
happens, replace the projector lamp with a new one as 
soon as possible.

Frequency

Displays the horizontal and vertical frequency of the 
computer.

Sync Polarity

Displays the sync polarity of the computer.

Sync Mode

Displays the sync mode of the computer.

Resolution

Displays the output resolution of the computer video 
output.

Refresh Rate

Displays the refresh rate of the computer video output.

Menu item

Description

Lamp

Displays the number of hours the current lamp has 
been used. The lamp light turns red when the projector 
lamp is near the end of its normal life. When this 
happens, replace the projector lamp with a new one as 
soon as possible.

Video Signal

Displays the input image signal mode.

Summary of Contents for EMP 9000 - SXGA LCD Projector












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands