manualshive.com logo in svg

Epson EB-Z10000, Installation Manual, Page: 65 / 84

Share
Download
Epson EB-Z10000 Installation Manual Download Page 65

t

 Indicator  is  lit  or  flashing  red

:   Lit  

:   Flashing  

:   Off

Status

Cause

Remedy or Status

Internal Error

Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address
provided in the Epson Projector Contact List. 

s

 "Epson Projector Contact List" 

p.74

Fan Error
Sensor Error
Cool System Error

Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address
provided in the Epson Projector Contact List. 

s

 "Epson Projector Contact List" 

p.74

High Temp Error
(overheating)

The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector
switches to standby mode, so check the following two points.

•

Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.

•

If the air filter is clogged, remove the power plug from the electrical outlet, and clean or replace it.

If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical
outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. 

s

 "Epson Projector

Contact List" 

p.74

When using at an altitude of 1500 m or more, set 

High Altitude Mode

 to 

On

.

Press the [Menu] button > 

Extended

 > 

Operation

 > 

High Altitude Mode

Set 

Direction

 to 

Pointing Down

, 

Pointing Up

, 

Angled Up

, or 

Angled Down

 when the projector is installed in a direction

which is not horizontal.
Press the [Menu] button > 

Extended

 > 

Direction

Lamp Error
Lamp Failure

Check the following two points after turning off the projector and removing the power plug from the electrical outlet.

•

Take out the lamp and check if it is cracked.

•

Clean the air filter.

If the lamp is not cracked

: Reinstall the lamp and connect the plug to an electrical outlet.

If the error continues

: Replace the lamp with a new lamp and connect the plug to an electrical outlet.

If the error continues

: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer

or the nearest address provided in the Epson Projector Contact List. 

s

 "Epson Projector Contact List" 

p.74

If it is cracked

: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot

be projected until the lamp is replaced.) 

s

 "Epson Projector Contact List" 

p.74

When using at an altitude of 1500 m or more, set 

High Altitude Mode

 to 

On

.

Press the [Menu] button > 

Extended

 > 

Operation

 > 

High Altitude Mode

Reading the Indicators

65

Summary of Contents for EB-Z10000





















































































Reviews:

No comments