background image

EPSON Endeavor L

SVGA feature

connector
Parallel

Serial

Keyboard

Mouse

Option slots

Speaker

Mass storage

Diskette drives

Hard disk

drives

Other devices

P r o g r a m

SVGA pass-through interface built into

main system board; 26-pin connector
One standard 8-bit parallel uni- or

bi-directional interface built into main

system board; I/O address selectable

through SETUP; 25-pin, D-shell connector
Two RS-232C, programmable,

asynchronous interfaces built into main

system board; 9-pin, D-shell connectors
PS/2 compatible keyboard interface built

into main system board; 6-pin, mini DIN

connector

PS/2 compatible mouse interface built into

main system board; 6-pin mini DIN

connector

Four 16-bit (or 8-bit) I/O expansion slots,

ISA compatible, 8.33 MHz bus speed; three

slots accommodate any size card, bottom

slot can hold a half size card
Internal, piezo-electric speaker on main

board
Internal mounts:

One 

 wide, half-height

Externally accessible mounts:

Two 5.25-inch wide, half-height

3.5-inch 

diskette drive, 720KB or 1.44MB

storage capacity

5.25-inch diskette drive, 360KB or 1.2MB

storage capacity

Combination diskette drive; 3.5-inch,

1.44MB and 5.25-inch, 1.2MB

 form factor hard disk drive(s), up

to half-height size; the first mounted in the

vertical internal bay and the second

mounted in an externally accessible,

horizontal bay
Half-height tape drive, CD-ROM drive,

optical drive, or other storage device;

 

or 

 

with mounting frames

Detachable, two-position height; 101 or

102 sculpted keys; country-dependent

main typewriter keyboard; numeric/

cursor control keypad; four-key cursor

control keypad; 12 function keys

Stored in ROM; accessible by pressing the

Delete 

key at the SETUP prompt during

boot

EPSON Endeavor L - 2

System security Password (up to 8 characters) defined in

SETUP for system boot and keyboard

unlock; definable hot key combination

locks the keyboard and mouse

Virus protection Write protection feature for boot sector of

the hard disk drive

 

Width

Depth
Height
weight

 

Type

Input ranges

Maximum

outputs
Frequency
Cables

14.8 inches (370 

mm)

16.5 inches (412 

mm)

4.8 inches (120 

mm)

16.7 lb (7.5 kg), with one diskette drive and

one hard disk, but without keyboard

85 Watt, Autosensing, UL listed, fan-cooled
100V to 125V

200V to 240v

+5 

VDC at 11 Amps, -5 VDC at 0.3 Amp,

+12 VDC at 2.0 Amps, -12 VDC at 0.3 Amp

50/60Hz

Two to main system board; four to mass

storage devices

 

 

 

Maximum current

+5 Volts

-5 volts

+12 Volts

-12 volts

For each 

slot

7 Amps

0.3 Amp

1.5 Amps

0.3 Amp

For all slots*

11 Amps

0.3 Amp          2 Amps

0.3 Amp

 

Condition

range

range

Storage range

Temperature

41° to 90° F

-4° to 140° F

-4° to 140° F

(5° to 32° C)

(-20° to 60° C)

(-20° to 60°C)

Humidity (non

20% to 90%

1O% to 90%

1O% to 90%

condensing)

Altitude

-330 to 9,900 ft

-330 to 39,600 ft     -330 to 39,600 ft

(-100 to 3,000 m) (-100 to 12,000 m) (-100 

to 

12,000 m)

Maximum wet

68° F (20° C)

104° F (40° C)

134° F (57° C)

bulb

Acoustical noise

37.5 dB

N/A

N/A

Summary of Contents for Computer











Reviews: