background image

2

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form 
or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of 
Seiko Epson Corporation. 

The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of 
this information as applied to other equipment. 

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for 
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this 
product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly 
comply with Seiko Epson Corporation’s operating and maintenance instructions.

Trademarks

Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. 

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their 
respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2009 Epson America, Inc. 7/09

CPD-27595

Summary of Contents for AP-60 - Projector Sound Solution





























Reviews: