Epson AcuLaser C8600 Reference Manual Download Page 214 | Manualshive

Page: 214 / 415

background image

212

Using Options

❏

The 500-Sheet Paper Cassette Unit weighs approximately
14 kg (31 lbs); always lift it with two people.

❏

When installing either unit on the printer, lock all casters at
the bottom of the unit.

❏

The printer weighs about 70 kg (154 lbs). One person should
not lift or carry it. Four people should carry the printer, lifting
it by the correct positions as shown below.

w

Warning:
If you lift the printer improperly, it may fall and injure you.

Installing the Large Capacity Paper Unit

The Large Capacity Paper Unit accommodates two paper
cassettes. The installation procedure for the optional Large
Capacity Paper Unit is the same as that for the 500-Sheet Paper
Cassette Unit. The illustrations below show an optional Large
Capacity Paper Unit with two paper cassettes.

Follow these steps to install the optional Large Capacity Paper
Unit or the 500-Sheet Paper Cassette Unit:

«
...
212
213
214
215
216
...
»

Summary of Contents for AcuLaser C8600
































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AcuLaser C8600

Brand: QuickLabel Systems Pages: 122

Brand: Lexmark Pages: 9

Brand: BenQ Pages: 6

Brand: Lexmark Pages: 4

WorkCentre WC7545

Brand: Xerox Pages: 8

Brand: Oce Pages: 32

Brand: Oki Pages: 94

Brand: Olivetti Pages: 558

Brand: Olivetti Pages: 315

SLK-TE20 Series

Brand: SEWOO Pages: 31

Brand: Xerox Pages: 342

Brand: CraftUnique Pages: 50

Brand: 3D Systems Pages: 83

Brand: Kyocera Pages: 44

Brand: D3D Pages: 6

Brand: SprintRay Pages: 6

Brand: Oki Pages: 56

Brand: SATO Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands