Epson ActionPC 2000 User Manual Download

Page: 36 / 129

Chapter 2

Using Your Computer

This chapter briefly describes the following operations:

Working comfortably

Inserting and removing diskettes

Stopping a command or program

Resetting the computer

Changing the processor speed.

Working Comfortably

This section provides some tips for creating a comfortable work
environment.

Use good posture. Keep your elbows, hips, and knees bent

at approximately 90 degree angles and keep your wrists as
close to horizontal as possible.

Vary your posture often and take frequent breaks. Stand
up, stretch, and move around.

Use a good chair. Make sure your chair supports your
lower back. A chair with padded armrests lets you rest
your arms as you work.

Keep your copy stand at the same eye level as your screen.
This reduces eye and neck strain. Also, rest your eyes
occasionally by closing them or focusing on a fixed spot in
the distance.

Using Your Computer

2-1

Summary of Contents for ActionPC 2000


































































































































Search results

Summary of Contents for ActionPC 2000

Reviews:

Related manuals for ActionPC 2000

Brands by name

Popular brands

Epson ActionPC 2000, User Manual

Search results

Summary of Contents for ActionPC 2000

Reviews:

Related manuals for ActionPC 2000

Brands by name

Popular brands