Epson 386 User Manual Download | Manualshive

Page: 75 / 218

background image

If you have only one diskette drive and no hard disk, you need to use

that drive to load the operating system as well as the application
programs you are using. First load the operating system; this copies it
to the computer’s memory (RAM) so you do not need to leave the
system diskette in the drive. Then you can remove that diskette and

insert the program diskette you want to use, and load that into

memory too. See your application program manual for detailed

instructions.

If you have a hard disk and one diskette drive, you can load the
operating system and application programs from the hard disk, create
and store your data there, and use the diskette drive just for copying
data to or from diskettes.

Using Two Diskette Drives

If you have two diskette drives, you can use the top drive (A) for

loading the operating system and application programs and the
second drive (B) for creating data. If you have a hard disk, you will

probably need the diskette drives just to copy files to and from the

hard disk and to copy diskettes.

Using a Hard Disk Drive

Working with a hard disk is similar to working with a diskette.
However, the hard disk provides several advantages:

l

The 40MB hard disk can store as much data as 33 1.2MB
diskettes and the 90MB hard disk can store the equivalent of

approximately 75 1.2MB diskettes.

_

l

Your computer can perform all disk-related operations faster.

l

You can store all your frequently used programs and data files on
the hard disk, eliminating the inconvenience of swapping

__

diskettes to access different files.

4-18

Using the Equity 386

«
...
73
74
75
76
77
...
»

Summary of Contents for 386



























































































































































































































Reviews:

No comments

Related manuals for 386

Brand: IBM Pages: 102

Brand: EUROCOM Pages: 113

Brand: DFI Pages: 13

Brand: Risecom Corporation Pages: 32

Brand: AZZA Pages: 12

Brand: Gateway Pages: 1

Brand: easescreen Pages: 4

Brand: Wacom Pages: 340

Brand: Advanced Micro Computers Pages: 86

Brand: NEC Pages: 110

Brand: NEC Pages: 2

PowerMate VT 300i Series

Brand: NEC Pages: 190

PowerMate Ready ES Pro

Brand: NEC Pages: 109

Ready 9734ES Pro

Brand: NEC Pages: 76

POWERMATE VT 300 RELEASE NOTES

Brand: NEC Pages: 192

Brand: NEC Pages: 253

PowerMate V100e

Brand: NEC Pages: 155

POWERMATE PROFESSIONAL PII

Brand: NEC Pages: 236

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands