EPPINGER HT Series Assembly Instructions Manual Download Page 5

Page: 5 / 15

Assembly instructions

(

translation

)

HT / SHT Gearboxes

Doc. No.: 1001

Version 2 dated 21/01/2019

Page 5/15

2.5

Contact

EGT EPPINGER Getriebe Technologie GmbH

Breitwiesenweg 2-8

73770 Denkendorf/Germany

+49 (0) 711 / 934 934-626

[email protected]

http://www.eppinger-gears.com

Handling and Transport

DANGER!

Death or extremely serious injury / crippling caused by falling loads.
During transport, never stay under suspended loads.

The weights indicated in Table 3 apply to gearboxes without motor
flange and with solid output shafts on both sides.

Gearbox

SHT100

HT90

SHT120

HT115

SHT150

HT140

HT170

HT215

Weight

about

4 kg

6 kg

10 kg

16 kg

35 kg

Table 3: Weights

Storage

The gearboxes have to be stored protected from dust, dirt and moisture.
The temperature has to be between -5°C and +40°C.

Assembly

CAUTION!

Assembly work may only be carried out by accordingly qualified trained
personnel.First of all, check the gearbox for external damage.

Summary of Contents for HT Series
















Search results

Summary of Contents for HT Series

Reviews:

Related manuals for HT Series

Brands by name

Popular brands

EPPINGER HT Series, Assembly Instructions Manual

Search results

Summary of Contents for HT Series

Reviews:

Related manuals for HT Series

Brands by name

Popular brands