EPOX P55-VP 2 User Manual Download Page 21

Page: 21 / 38

3-12 CHAPTER 3

ROM PCI/ISA BIOS(2A5LDPA9)

INTEGRATED PERIPHERALS

WARD SOFTWARE, INC.

IDE HDD Block Mode:

The default value is Enabled.

Enabled

Enabled IDE HDD Block Mode. The HDD transfer rate is better than

Disable.

Disabled

Disable IDE HDD Block Mode.

PCI Slot IDE 2nd Channel:

The default value is Enabled.

Enabled

Enable secondary IDE port and BIOS will assign IRQ15 for this port.

Disabled

Disable secondary IDE port and IRQ15 is available for other device.

If you don't use the Onboard IDE connector, then use On-card
(PCI or ISA card) IDE connector. You have to set Onboard Primary
PCI IDE: Disabled and Onboard Secondary PCI IDE: Disabled
from CHIPSET FEATURES SETUP UTILITY.

The Onboard PCI IDE cable should be

equal to or less than

18 inches (45 cm.).

Onboard Primary PCI IDE:

The default value is Enabled.

Enabled

Enable Onboard 1st channel IDE port.

Disabled

Disable Onboard 1st channel IDE port. When use On-card (PCI or ISA

card) IDE connector.

Onboard Secondary PCI IDE:

The default value is Enabled.

Enabled

Enable Onboard 2nd channel IDE port.

Disabled

Disable Onboard 2nd channel IDE port When use On-card (PCI or ISA

card) IDE connector.

3-6 INTEGRATED PERIPHERALS

Note:

ESC : Quit : Select Item
F1 : Help PU/PD/+/- : Modify
F5 : No Change (Shift) F2 : Color
F7 : Load Setup Defaults

Onboard Primary PCI IDE

: Enabled

Onboard Parallel Port

: 378/IRQ7

Onboard Secondary PCI IDE

: Enabled

Onboard Parallel Mode

: ECP / EPP

IDE Prefetch Mode

: Enabled

ECP Mode Use DMA

: 3

IDE HDD Block Mode

: Enabled

Parallel Port EPP Type

: EPP1.9

IDE primary Master PIO

: Auto

IDE Primary Slave PIO

: Auto

Onboard USB Controller

: Disabled

IDE Secondary Master PIO

: Auto

IDE Secondary Slave PIO

: Auto

IDE Primary Master UDMA

: Auto

IDE Primary Slave UDMA

: Auto

IDE Secondary Master UDMA

: Auto

IDE Secondary Slave UDMA

: Auto

PCI IDE Secondary Channel

: Enabled

Onboard FDC Controller

: Enabled

UART 2 Mode

: Standard

Summary of Contents for P55-VP 2







































Search results

Summary of Contents for P55-VP 2

Reviews:

Related manuals for P55-VP 2

Brands by name

Popular brands

EPOX P55-VP 2, User Manual

Search results

Summary of Contents for P55-VP 2

Reviews:

Related manuals for P55-VP 2

Brands by name

Popular brands