manualshive.com logo in svg

EPOX EP-3VBA, User Manual, Page: 2 / 63

Share
Download
EPOX EP-3VBA User Manual Download Page 2

EP-3VBA

Technical Support Services

If you need additional information, help during installation or normal use of this
product, please contact your retailer.  If your retailer can not help, you may E-
Mail us with any questions at the following address [email protected]

Record your serial number before installing your EP-3VBA mainboard. (the serial
number is located near the ISA slots at the edge of the board)

EPoX EP-3VBA  serial number:

__________________________

BIOS Upgrades

Please use either our Web Site or BBS for current BIOS Upgrades.

Internet Access

http://www.epox.com
http://www.epox.com.tw
[email protected]
[email protected]

Modem Access

886-2-2247-2742 (Taiwan)
31-182-618451 (The Netherlands)

You can access this number via a Hayes-compatible modem with a 2,400 to
28,800 baud rate.  The following setup format is required:

8 Data Bits, No Parity, 1 Stop Bit.

If your modem is unable to connect at higher baud rates, try connecting at
2,400 baud before contacting Technical Support.

Thank you for using EPoX mainboards!

© Copyright 1998 EPoX Computer Company. All rights reserved.

Summary of Contents for EP-3VBA
































































Reviews:

No comments