background image

page | 15

© 2016 Episode®

Once setup is complete, all OvrC features can now be accessed via a smartphone or tablet 
application, or via the internet at www.OvrC.com

SPECIFICATIONS

ESA-70V2CH-150W

ESA-70V2CH-300W

ESA-70V2CH-500W

Continuous Power 
Output (All Channels)

150w per channel 
@ 70V

300w per channel 
@ 70V

500w per channel 
@ 70V

Inputs per Channel

1 unbalanced (RCA) and 1 balanced (set-screw)

Input Sensitivity

775mV

Input Impedance

10KΩ (unbalanced); 20KΩ ( balanced)

AUTO ON  Sensitivity

2.5mV

12 Volt Trigger Input

4.5-12V DC; 10K Ω

12 Volt Trigger Output

12V DC; 10mA

S/N ratio

95db A-weighted

Frequency Response

50 Hz to 20KHz

Distortion

0.1% THD 20 Hz-20 kHz

Input Voltage

115V AC/230V AC

Fuse

115V AC

T3.15AL 250V

T6.3AL 250V

T10AL 250V

230V AC

T1.6AL 250V

T3.15AL 250V

T5AL 250V

Power Consumption

400 watts

800 watts

1200 watts

Dimensions (Inches)

17"W x 1.73"H x 14"D

17"W x 3.49"H x 
15”D

Weight

7.8 lbs

13.56 lbs

18.00 lbs

Certification

Meets FCC Part 15, UL EN60065

DIMENSIONS

19.00in.

17.00in.

1.73in. 2.10in.

19.00in.

17.00in.

3.49in 3.86in

14.00in.

15.00in.

PROT -30 -20 -10 CLIP

1

2

ECA-70IPAMP-2D-150

PROT -30 -20 -10 CLIP

1

2

ESA-70V2CH-500W

Summary of Contents for ESA-70V2CH-150W

















Reviews: