epiphan video Standalone VGA Grid User Manual Download | Manualshive

Page: 272 / 319

background image

Standalone VGA Grid User
Guide

Storage disk maintenance

Storage disk maintenance

Your Standalone VGA Grid is equipped with one or more hard drives for storage of recordings. Occasionally,
maintenance is required for these disks. This section describes procedures for the following topics:

l

Check disk storage space

l

Schedule disk check

l

Perform disk check

l

Rebuild or replace storage disks

l

Verify RAID storage

l

Read data from removed storage disks

Check disk storage space

Standalone VGA Grid has a finite amount of storage . By default, the standalone and networked version have
3 TB of storage. This storage space holds a lot of recordings, but it can get full. It’s a good idea to monitor your
current disk usage.

If available storage is low, consider removing some unneeded recordings or setting up an automatic file
transfer with deletion after transfer. See

and

File and recording transfer

.

Disk space can also be checked via the tablet interface. See

Verify disk space via the tablet

.

To check disk storage space:

1. Connect to the admin interface using your preferred connection mechanism. See

Connect to the admin

2. Login as admin or operator.

3. Check the

Internal Storage

section at the bottom of the menu column. The bar will be mostly green if

there is lots of space left, or mostly red if storage space is nearly full.

272

«
...
270
271
272
273
274
...
»

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

Dial-to-IP 5301-DC

Brand: Accelerated Pages: 26

Brand: Cambridge Audio Pages: 2

Brand: Datavideo Pages: 10

Brand: VAD Pages: 18

INDUSTRIAL Series

Brand: ICT Pages: 2

Brand: Xcube Pages: 20

Brand: Grundig Pages: 12

Brand: Nextar Pages: 30

Brand: Clever Little Box Pages: 56

Brand: Marantz Pages: 77

EZ season MX-110D

Brand: FUNAI Pages: 35

Brand: Cary Audio Design Pages: 2

Brand: April Music Pages: 20

Brand: Hyundai Pages: 60

Brand: Coby Pages: 2

ControlMaster Edge

Brand: R&M Pages: 2

Brand: THOMSON Pages: 39

Brand: Curtis Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands