manualshive.com logo in svg

epiphan video Standalone VGA Grid, User Manual

The Epiphan Standalone VGA Grid is a cutting-edge hardware device that allows users to connect multiple VGA sources to a single display. You can easily set up and operate this device with the help of our comprehensive User Manual, available for free download on our website. Unlock the full potential of your Epiphan Standalone VGA Grid with our detailed instructions and troubleshooting tips, seamlessly accessible at manualshive.com.

Share
Download
background image

Standalone VGA Grid User Guide                                     

Connect a source

Audio sources

Standalone VGA Grid's web interface also automatically discovers all audio sources displays them in the same 
section. Audio sources are identified by the word audio in the source name. Audio input devices such as a 
microphone and portable music players can send audio signals to the Standalone VGA Grid using the audio 
input ports at the back of the system. Audio is also supported via HDMI and SDI.

DVI2PCIe cards do not support audio over HDMI. Standalone VGA Grid systems with DVI2PCIe 
cards will not be able to capture audio through HDMI sources.

This chapter covers the following sections:

 

l

Connect a source

 

l

Preview a source

 

l

Rename a source

 

l

Control audio volume

 

l

Confirm audio levels

 

l

Add a No Signal image to a source      

Connect a source

You can connect sources to the Standalone VGA Grid at any time, either before or after the system is powered 
on. Similarly you can disconnect a source from a port and even connect a different source at any time. 

Changing the source connected to a port that is being streamed or recorded can result in the 
recording stopping or the stream frame size changing depending on how your channel is 
configured. 

If the frame size changes, viewers may be disconnected and need to re-connect to the stream. 

Connect the input sources to the following input ports on the system:

Table 18 

Cable and port connections

Cable

Input Port

VGA, HDMI* or DVl

DVI port 

SDI

SDI port

125

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

MADRIX ORION Technical Manual & Quick Start Manual preview
ORION
Brand: MADRIX Pages: 36
Caliber MCD893 Operating Instructions Manual preview
MCD893
Brand: Caliber Pages: 26
OT Systems FT210AB Series Installation And Operation Manual preview
FT210AB Series
Brand: OT Systems Pages: 16
E-Lektron EL651031 Manual preview
EL651031
Brand: E-Lektron Pages: 7
Coretec VCX-7401 Installation And Operating Instructions Manual preview
VCX-7401
Brand: Coretec Pages: 38
DELTACAST DELTA-neo N2H User Manual preview
DELTA-neo N2H
Brand: DELTACAST Pages: 40
Monoprice VD-101 User Manual preview
VD-101
Brand: Monoprice Pages: 2
Technics RS-TR333 - SCHEMATICS Manual preview
RS-TR333 - SCHEMATICS
Brand: Technics Pages: 8
Extron electronics Sync Converter/Stabilizer SCS 300 Specification Sheet preview
Sync Converter/Stabilizer SCS 300
Brand: Extron electronics Pages: 1
M-Audio Mac Syncman Manual preview
Mac Syncman
Brand: M-Audio Pages: 24
Cambridge Audio Topaz CD5 User Manual preview
Topaz CD5
Brand: Cambridge Audio Pages: 10
Soundfield UPM-1 User Manual preview
UPM-1
Brand: Soundfield Pages: 13
ELECTROCOMPANIET RENA S-1 Quick Start Manual preview
RENA S-1
Brand: ELECTROCOMPANIET Pages: 16
BORK DV VNM 1345 SI Maintenance Manual preview
DV VNM 1345 SI
Brand: BORK Pages: 39
Microsens GE-C301 User Manual preview
GE-C301
Brand: Microsens Pages: 2
NAD T533CT Service Manual preview
T533CT
Brand: NAD Pages: 79
i. Tech Dynamic Powbox V25 Owner'S Manual preview
Powbox V25
Brand: i. Tech Dynamic Pages: 19
Pentax EPK-1000 Owner'S Manual preview
EPK-1000
Brand: Pentax Pages: 44

Brands by name

Popular brands

Load more brands