background image

                                         

BEIJING EPSOLAR TECHNOLOGY CO.,LTD. 

2

 

1. Overview

 

The  GoMate  is  a  negative-ground,  flush  mount  solar  charge  controller, 
designed for an aesthetically clean and integrated look on RV and Vessel, 
also  included  surface  mount  cover  to  suit  personal  preference.  The 
GoMate  adopts  highly  efficient  PWM  charging  mode,  also  comes 
equipped with special LCD display to show the real-time operating status 
of  the  system.  This  charge  controller  is  fully  controlled  automatically, 
which provide simple usage pattern to users.   
 

Features

 

  Flush mounted and embedded installation design 

  High  quality  and  low  failure  rate  components  (ST/IR)  to  ensure  the 

product lifetime 

  3-Stage intelligent PWM charging: Bulk, Boost/Equalize and Float 

  Battery type:

 

Sealed, Gel, Flooded, and User 

  Real-time energy statistics feature 

  Battery temperature compensation feature 

  Digital LCD monitor for informative display of operational parameters 

and fault messages 

  Voltage drop and temperature compensation sampling interface design 

  RS485 communication port with Modbus protocol, and short circuit 

protection for 5V/200mA power supply 

  Multiple communication peripherals 

  Rated charging current at working temperature without de-rating 

  Extensive electronic protections 

  Monitor and set the parameters via PC software

 

or APP 

 

 

Summary of Contents for GM3024N





















Reviews: