background image

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING THIS UNIT CALL

0345 27 27 810

05

 Installation Instructions  

05

IMPORTANT

Be sure to have read and understood these 

instructions before beginning the installation 

process.

PRE-INSTALLATION CHECK LIST

Make sure that the unit can physically fit in to 

the desired location.
The energiSava 250 unit should be 

situated so that access for maintenance or 

replacement of parts is possible. Make the 

ductwork runs as short as possible. Having 

the most direct route and using as few 

bends as possible will reduce air resistance 

and improve the efficiency of the unit.

SAFETY AND RECOMMENDATIONS

• All wiring must comply with Building 

Regulations and the current I.E.E. Wiring 

Regulations (BS7671) or the equivalent 

standards  for  your  country.  The  final 

installation should be examined and tested 

by a qualified electrician.

• Precautions must be taken to avoid the 

back-flow of gases into the dwelling from 

the open flue of gas or other fuel-burning 

appliances.

• Make sure the mains supply complies with 

the rating label for voltage, frequency and 

phase.

• This appliance can be used by children 

aged from 8 years and above and 

persons with reduced physical, sensory or 

mental capabilities or lack of experience 

and knowledge if they have been given 

supervision or instruction concerning 

use of the appliance in a safe way and 

understand the hazards involved. Children 

shall not play with the appliance. Cleaning 

and user maintenance shall not be made 

by children without supervision.

Summary of Contents for energisava250





















Reviews: